Bus T2 - cylinder heads Typ 2/4 für 1,7-2,0
Novelties
No results were found for the filter!
Cylinder head complete (each)
Type 4 engines 1700 cc Even with complete cylinder heads, it is always advisable to perform a leak test before installing the cylinder head, because this is the only way to be certain. For specialists, this should be a matter of course,...
Cylinder head complete (each)
Type 4 engines 1800 cc Even with complete cylinder heads, it is always advisable to perform a leak test before installing the cylinder head, because this is the only way to be certain. For specialists, this should be a matter of course,...
Cylinder head complete (each)
Type 4 engines 2000 cc until 07/78 Even with complete cylinder heads, it is always advisable to perform a leak test before installing the cylinder head, because this is the only way to be certain. For specialists, this should be a matter...
in stock
Cylinder head nuts M10 (16 pieces), fit from 08/55
fit for Type 3 engines Type 4 engines Type 1 engines (from engine no. 1 120 615)
Cylinder head with big valves (39.3 x 33.0) (each)
Type 4 engines 2000 cc until 07/78 Even with complete cylinder heads, it is always advisable to perform a leak test before installing the cylinder head, because this is the only way to be certain. For specialists, this should be a matter...
Cylinder head, complete, for Type 4 engines code CU & CV
Even with complete cylinder heads, it is always advisable to perform a leak test before installing the cylinder head, because this is the only way to be certain. For specialists, this should be a matter of course, because failure to do...
Gasket between intake manifold and cylinder head, fits Bus T2 & T3 (08/75 to 12/82)
for vehicles with fuel injection fits for Bus T2 (engine code GD & GE) Bus T3 (engine code CV) original spare part, NOS few available
in stock
Inlet valves 39.3 x 8 mm (4 pieces)
fits for: Type 4 engine 1700 cc Type 4 engine 1800 cc with enginecode AP 08/1974 and later Type 4 engine 1800 cc with enginecode ED Type 4 engine 2000 cc 08/1979 and later
in stock
Mutter für Zylinderkopf M10, passend ab 08/55
passend für Typ 1-Motoren (ab Motor-Nr. 1 - 1 120 615) Typ 3-Motoren Typ 4-Motoren Original-Ersatzteil, NOS wenige vorhanden
in stock
Outlet valves 33.0 x 9 mm (4 pieces)
fits for: Type 4 engine 1700 cc Type 4 engine 1800 cc with enginecode AP 08/1974 and later Type 4 engine 2000 cc
in stock
Set of valve guides, 1st oversize, fits Type 4 engines & WBX
bronze alloy with high wear resistance and good fatigue and corrosion resistance for inlet valves inner dimension 7.99 mm outer dimension 12,11 mm length 61mm
in stock
Set of valve guides, 1st oversize, fits Type 4 engines & WBX
bronze alloy with high wear resistance and good fatigue and corrosion resistance for exhaust valves inner dimension 8.98mm outer dimension 13.11 mm length 66.5mm
in stock
Set of valve guides, 2nd oversize, fits Type 4 engines & WBX
bronze alloy with high wear resistance and good fatigue and corrosion resistance for inlet valves inner dimension 7.99 mm outer dimension 12.21 mm length 61mm
Set of valve guides, 2nd oversize, fits Type 4 engines & WBX
bronze alloy with high wear resistance and good fatigue and corrosion resistance for exhaust valves inner dimension 8.98mm outer dimension 13.21 mm length 66.5mm
in stock
Stiftschraube für Kipphebelachse, passend für verschiedene Modelle
teilweise passend ab 34 PS für Käfer Karmann Ghia Typ 34 Bus T1 Bus T2 Typ 3 Typ 34 Kübelwagen Typ 181 Fridolin Typ 147 Bus T3 Maße der Stiftschraube M8/M10,gesamt 62 mm lang
in stock
stud for rocker arm axle, Type 4, T2 & T3
fits for. Type 4 T2 (Type 4 engine) T3 (to 07/85, CU & CV engines)
in stock
T-Piece Connector for Servo Line to inlet Manifold
passend für Bus T2 1,7-2,0 bis 07/79 passend für T3 Bus nur CU 2,0 luftgekühlt 79-83
in stock
Valve guide, inlet, 8 mm, fits for Bus T2 + T3
fits for: 914, 1.7-1.8, 01/69-12/73 Bus T2 1.7-1.8, 08/71-07/75 Bus T2 + T3, 2.0, 08/75-12/82
Viewed