Bus T2 - rear axle

Novelties
No results were found for the filter!
Adujstable spring plates, fits for Bus T2B, 71-79
These high-quality 2-piece constructed springplates are 25mm lower than standard springplates. They feature a fully adjustable rear end lowering plus a much easier change of rear tyres. Adujstable spring plates fits for: Bus T2B, 71-79...
in stock
Anschlagbuchsen des Anschlagbügels, passend für Bus T2 (08/71 bis 11/74)
passend für Bus T2 (FIN 212 2000 001 bis 214 2063 527) Original-Ersatzteil, NOS nur wenige vorhanden
in stock
Bearing rubber for rear axle strut, fits for Bus T2
Bearing rubber for rear axle strut fits for: Bus T2
in stock
Cap screw, M8x48, for constant velocity joint (24 pieces recommended)
fits for: Golf/Jetta, 1.1-1.8 (incl. D), 02/74-02/84 Golf/Jetta, 1.0-1.8 (incl. D), 08/83-12/92 Bus T3, 1.6-2.1 (incl. D), 05/79-07/92 Porsche 914, 1.7-2.0, 01/69-02/76
in stock
Castle nut M 30 x 1.5, suitable for Bus (08/63 to 07/92)
wrench size 46 mm fits for Bus T1 (from VIN 1 144 282) Bus T2 Bus T3
in stock
Cotter for castellated nut, fits various models
5mm x 55mm fits for Bus T1 (from FIN 1 144 281) Bus T2 Bus T3 Type 181 Thing Do not reuse cotters, always replace them!
in stock
Drive shaft, complete with collars and bolts, rear left, 457 mm
Drive shaft complete with sleeves and bolts rear left 457 mm for automatic transmission and with independent suspension fits for: Bus T2, 1.6-2.0, 08/67-07/79
in stock
Drive shaft, complete with collars and bolts, rear right, 505 mm
Drive shaft complete with sleeves and bolts rear right 505 mm for automatic transmission and with independent suspension fits for: Bus T2, 1.6-2.0, 08/67-07/79
in stock
Federscheibe für verschiedene Befestigungen bei Fahrzeugen mit Schräglenkerachse
12 x 24 passend für u.a. Befestigung der Hinterachsstrebe Bus T2 Befestigung der Federstrebe Käfer Karmann Ghia Typ 14 & Typ 34 Typ 181 Typ 3 Original-Ersatzteil, NOS begrenzte Stückzahl
in stock
Gehäuse für Anschlagbügel, passend für Bus T2 (ab 08/75)
passend für Bus T2 (ab FIN 216 2000 001) Original-Ersatzteil, NOS wenige vorhanden
in stock
Hose tie for joint protection boot, fits Bus T2 & T3
fits for Bus T2 Bus T3 original spare part, NOS few available
Radlagersatz hinten, passend für Bus T2 & T3
bestehend aus 1x Radlager innen (FAG) 2x Wellendichtring für Radlager (GOETZE) 1x Sicherungsring 72 x 2,5 1x Lithiumfett 1x Splint für Kronenmutter OEM-Ersatzteil, NOS Einzelstück
in stock
Reparatursatz Gleichlaufgelenk passend für Modelle von 08/67-07/92
passend für: Bus ab Bj 68 - 91 Kübel ab Bj 08/73 411/ 412
in stock
Rubber stop for torsion bar, fits various models
fits for: Bus T1 (1500 & from VIN 214 2063 527) Type 3 Squareback (up to VIN 366 500 000) Type 181 Bus T2 (except ambulance) made by WERK34
in stock
Safety snap ring for drive shaft head
fits for: Beetle, Inclined control arm rear axle Typ 3, Inclined control arm rear axle Karmann Ghia, Inclined control arm rear axle Typ 34, Inclined control arm rear axle Bus T2, 1968-79 Bus T3 Golf MK1 Golf MK2
in stock
Sealing cap for flange
fits for Bus T2 Bus T3 (manual transmission) Bus T4 (up to transmission no. 06034)
in stock
Shaft seal rear wheel bearing, fits Bus T2 & T3
fits for Bus T2 68-79 Bus T3 80-92 original spare part part numbers for comparison: 211 501 317, 211 501 317 A & 211 501 317 B
in stock
Shaft seal to drive shaft, fits for bus T2 08 / 68-07 / 75
fits for right or left. Not suitable for automatic. OEM Made in Germany
in stock
Shaft seal to drive shaft, fits for bus T2 from 08/75 and T3
Fits for right or left Not for automatic OE quality Made in Germany
in stock
Wheel bolt rear, fits Bus T3 & Bus T2 (from 08/70)
Length 34,5mm length 34,5mm fits for Bus T2 (from VIN 211 2000 001) Bus T3
in stock
Zylinderschraube für Gleichlaufgelenk, passend für Bus T2 (bis 07/70)
M8 x 47 passend für Bus T2 (bis FIN 210 2300 000) Original-Ersatzteil, NOS begrenzte Stückzahl
Viewed