Bus T2 - front axle

Novelties
No results were found for the filter!
Carrying Lever right bottom with Carrying Joint T 2, overhau
Bus, please indicate whether 1.0 or 1.2 tons of additional load are present!
in stock
Carrying lever stop below, fit for buses from 08/67-07/79 T 2
Fitting Position: Torsion Bar, Lower Front Axle Material: Elastomer
in stock
Carrying lever, left, below, with ball joint, suitable for Bus T2 up to 07/69, overhauled in AT
Carrying lever left below with ball joint suitable for Bus T2 up to 07/69 overhauled in AT
Front Axle Body, 8/69 - 7/79 only fit 1,2 t front axle weight
only 1.2 ton ! many buses have only a front axle load of 1.0t there this axle does not fit !!!! bearing lever, spring assembly, spring assembly fastening are different than those of a 1.0 ton axle! original spare part, NOS with mounting...
Inner spacer for wheel bearing, fits for Bus T2 (up to 07/70)
fits for Bus T2 (up to VIN 210 2300 000) original spare part NOS only few available
Lagerbuchse für Traghebel, passend für Bus T2
es werden 4 Stück pro Fahrzeug benötigt passend für Bus T2 Original-Ersatzteil, NOS wenige vorhanden
in stock
Nut for suspension joint and tie rod, M 18 x 1.5, self-locking, fits Bus T2, T3 and LT
fits for Bus T2 Bus T3 (Syncro as well) also suitable for tie rod LT (1st generation) T2 Mexico M 18 x 1,5 Original spare part, NOS Limited quantity
in stock
Nut for the right spindle, fits for Bus T2 08/67-07/79
Nut for the right spindle fits for: Bus T2, 08/67-07/79
in stock
Puma Style lowering system(weld on adjuster) per Pair Bus until 07/79
Mit den Rasterplatten können Sie Ihre vorhandene Original-Vorderachse in eine verstellbare 'Puma-Achse' umbauen. Die präzise Feinverzahnung erlaubt eine perfekte Höhen- und Härte-Justierung vorzunehmen. Das flache Design, das trotzdem...
in stock
Radbolzen vorne, passend für Bus T3 & Bus T2 (ab 08/70)
Länge 52mm passend für Bus T2 (ab FIN 211 2000 001) Bus T3 Original-Ersatzteil, NOS begrenzte Stückzahl
in stock
Replacment boot for ball joint for front torsion arm, fits for bus T2
passend für T2 68-79 oben und unten Passend für T3 80-92 nur unten
in stock
Standard ball joint for front torsion arm, fits for bus T2
fitting details: The outer diameter of this ball joint (at the knurl section) is 48.3mm. There should be a minimum overlap/interference of 0.2mm between the joint and the torsion arm bore. It is important that the torsion arm bore is...
in stock
Steering knuckle set, dropped, for ball joint
Mit diesen Achsschenkeln können Sie Ihren Bus rund 6cm dem Boden näher bringen, selbstverständlich können alle anderen Achsteile wie Tragarme, Spurstangenköpfe und Kugelgelenke weiter verwendet werden. Wir empfehlen in diesem...
Traghebel rechts unten mit Traggelenk Bus T2 (bis 07/69), überholt im AT
Bolzenlänge Stoßdämpferbefestigung 45 mm passend für Bus T2 bis 07/69 überholt im Austausch Altteillieferung vorab Lagerstellen des Traghebels dürfen nicht stark verschlissen sein oder Fressspuren haben
Viewed