Typ 3 1500 | 1600 - engine

Novelties
No results were found for the filter!
in stock
123 ignition with vacuum-advance
Intended for standard ex-factory engines which always feature a vacuum for acceleration. Many replaced their standard power Distributor by a Distributor without vacuum advance, a wrong decision. The ignition timing is withdrawn than...
in stock
123 ignition without vacuum-advance
Intended for tuned engines with larger carburetor drive which in most cases no vacuum for advance capabilities. Because the way of carburetor to cylinder head is a lot shorter than with a standard engine has practically no pull this...
123 TUNE ignition for carburetor engines
suitable for: all 1.2-1.6 engines (except 25-30 HP) T3 CT / CZ / CU and all Type 4 engines not suitable for injectors maintenance-free technology, particularly suitable for modified engines
123 Zündverteiler, für D-Jetronic
passend für : Typ 1-Motoren Typ 3-Motoren Typ 4 Motoren mit D-Jetronic
69 mm Counter-weighted crankshaft, 4140 Chromoly
69 mm Counter-weighted crankshaft 4140 Chromoly fits for 181 Thing 09/69-02/79, 1.5-1.6 Karmann Ghia 08/66-12/76, 1.3-1.6 Bus T1 08/63-07/67, 1.5 Bus T2 08/67-07/71, 1.6 Type1 incl. 1302/1303 08/65-03/81, 1.3-1.6 Type3 08/65-07/73, 1.5-1.6
in stock
Actuating shaft for carburettor, fit for type 3/34 (08/63 to 10/64)
fits for: Type 3/34 (engine no. 260 979 to 713 138) single-carburettor engine originalsparepart, NOS only few available
Adapter-Dichtsatz für Ölkühler, passend für Typ 1- & Typ 3-Motoren
für den Einbau von Ölkühlern ab 08/69 in Motoren bis 07/69 Ölkühlern bis 07/69 in Motoren ab 08/69 bestehend aus 2x Dichtring 8mm/10mm 3x Scheibe Einbauanleitung Original-Ersatzteilsatz, NOS wenige vorhanden
in stock
Additional air regulator for injection, fits Type 3 automatic (from 08/69)
fits for Type 3 (from engine no. U 0 231 101) only with automatic transmission original spare part, NOS single item
in stock
Air baffle bottom left, galvanized, top quality, fits 29-37 kW (40-50 hp)
This galvanized air baffle for the pushrod protection tubes has the nuts and mounting holes in place. No rework is necessary as with the inexpensive repros.
in stock
Air baffle bottom, front right, galvanized, top quality, 25 kW (34 hp)
This galvanized air baffle for the pushrod protection tubes has the nuts and mounting holes in place. No rework is necessary as with the inexpensive repros.
in stock
Air filter for twin carburetor engine, fits for Karmann Ghia Type 34 + Type 3, used
Air filter for twin carburetor engine fits for: Karmann Ghia Type 34 Type 3 used
in stock
Air funnel 21.5 mm for carburetor, fit for type 3/34 (08/63 to 07/64)
fits for: carburetor 32 PDSIT Type 3 (engine no. 255 340 to 633 330) Type 34 (engine no. 255 340 to 633 330) Originalsparepart only few available
Alu-Valve covers with ventilation , Evolution Type 1
German Product fits all Typ 1 engines except 24,5-30 HP
in stock
Aluminum oil cooler, standard
suitable for: Beetle, 1.6 year of construction 08/70 to 04/79 Bus T2, 1.6 from 08/70 to 07/71 Golf GTI, 1.6 + 1.8 GTI year 01/77 to 02/84 Scirocco GTI, 1.6 + 1.8 from 01/77 to 10/83
Ausrückwelle, passend für verschiedene Modelle (08/70 bis 09/71)
passend für Käfer (FIN 111 2000 001 bis 112 2070 812; alle 1302 , nicht Standard mit kurzem Vorderwagen) Karmann Ghia Typ 14 (FIN 141 2000 001 bis 142 2070 812) Typ 181 (FIN 181 200 001 bis 181 3200 000) Typ 3 (FIN 311 2000 001 bis...
Automatic choke, 6 V left, fit for Type 3/34 (08/63 to 07/66)
fits for: carburetor 32 PDSIT-2 Type 3/34 (from engine no. 255 340 & T 0 000 001 to T 0 0260 000) Originalsparepart
in stock
Automatic choke, 6 V left, fit for Type 3/34 (08/63 to 07/66)
fits for: carburetor 32 PDSIT-2 Type 3/34 (from engine no. 255 340 & T 0 000 001 to T 0 0260 000) Originalsparepart
in stock
Automatic choke, 6 V right, fit for Type 3/34 (08/63 to 07/66)
fits for: carburetor 32 PDSIT-3 Type 3/34 (from engine no. 255 340 & T 0 000 001 to T 0 0260 000) Originalsparepart only few available
in stock
Automatic choke, 6 V, fit for Type 3/34 (up to 07/66)
fits for: carburetor 32 PHN Type 3/34 (up to engine no. K 0 060 000) Originalsparepart only few available
in stock
Baffle plate for cylinder
MODEL Engine Construction Year Beetle 1.2-1.6 08/65-12/77 T1 1303 1.3-1.6 08/70-04/79 Bus 1.5-1.6 01/63-07/71 Type 3 1.5-1.6 04/61-07/73
Bearing bolt for fixing the throttle cable, NOS
Bearing bolt for fixing the throttle cable fits for Type 1 (1974 - 1986) Karmann Ghia (1956 - 1974) Golf (1975 - 1976) 181 (1969 - 1982) LT (1975 - 1983) Passat (1974 - 1980) T2 (1968 - 1985) T3 (1961 - 1974) NOS
in stock
Bearing bolt for intermediate piece, suitable for Type 3/34 (08/63 to 07/65)
fits for: two-carburetor engine Type 3/34 (up to engine no. 1 100 000) original spare part only few available
in stock
Bearing for fuel pump, fit for Type 3/34 & Type 4
fit for: Type 3/34 Type 4 only for engines with fuel injection Originalsparepart, NOS only few available
in stock
Bearing pin for angle lever, fit for type 3/34 (from 08/63)
fit for: Dual carburetor engine Type 3/34 (from engine no. 255 340) Originalsparepart, NOS only a few available
Big Pack Engine Gasket Kit 25kw (34PS) 1,2 after 08/60
Das große Set bestehend aus Motordichtsatz Simmering Kurbelwelle Öl-Sieb Stößelschutzrohre Spannbügel passend für 1.2 Liter Motoren ab 08/60
Big Pack Engine Gasket Kit fits 1,3-1,6 Engines
Das große Set bestehend aus Motordichtsatz Simmering Kurbelwelle Öl-Sieb Stößelschutzrohre Spannbügel passend für 1.3-1.6 Liter Motoren
in stock
Bolt for throttle cable, fit for Type 3/34 (from 08/65)
fits for: two-carburetor engine Type 3/34 (from engine no. T 0 000 001) originalsparepart
in stock
Bracket for distributor, T2, Type 3, Type 34 & Type 181
fits for: T2 Type 3 Type 34 Type 181 Originalsparepart
Cage for engine mounting with rubber bearing, fits for Typ 3 with swing axle
Cage for motor bearing with rubber bearing fits for: Typ 3, (Notchback, TL and Variant) Karmann Ghia Typ 34 with swing axle
in stock
Cage for rear engine mounting, fits for all models up to 07/68
Cage for rear mounting fits for Karmann Ghia Type 3 all models up to 07/68
in stock
Cam Shaft Drive Gear 25-37 kW (34-50 PS) + WBX
Fits: Type 1 (except 25 and 30 hp) Type 3 CT Water boxer engines
in stock
Cam Shaft Kit, Engle W 110, suitable for Type 1
consisting of: Sport cam shaft 284 degrees Beam Springs Hardware
in stock
Cam Shaft with Wheel Series (3-Point), fit for Engines until 07/71
fit for engine 25-37 kW (34-50) Up to year of construction 07/71
in stock
Cam Shaft-Set Engle W120 fit for Typ 1 Engines
Set consisting of Sports camshaft 294 degrees Plunger Tappet springs Small parts
in stock
Camshaft bearing set, shaft: 0.25, housing: standard
Manufacturer Kolbenschmidt Originalpartnumber is only used for comparison 111 198 543
in stock
Camshaft Bearing WBX Standard
fit for: Beetle, Karmann, Type 3, Bus T1 and T2 1.2-1.6 from 08/60 Thing from 08/69 Bus T3 CT / CZ engine 1.6 Bus T3 1.9 WBX 83-07 / 85 If a double collar bearing is needed, you need two bearing sets.
Capacitor for ignition distributor, fits various models
fits for the following ignition distributors 113 905 205 B / 113 905 205 J / 113 905 205 L please note: length of the cable approx. 65mm In the 60's, several very similar condensers were installed. Their main difference is the length of...
Carburetor 32 PHN fit for 1.5 with 12 volts
Der Vergaser wird in 12V-Ausführung geliefert. Sollten Sie die 6V-Ausführung benötigen, geben Sie dies bitte bei der Bestellung an. Die Altteil-Kaution in Höhe von 100,00 EUR ist im Kaufpreis enthalten und wird bei tauschfähigen und...
Viewed