181 Thing - Alternators
Novelties
No results were found for the filter!
108mm Dynamo/Alternator Top Pulley “C” Spanner
This “C” Spanner has been made to fit top pulleys with a diameter of 108mm, hooks into the notch on the rear of the pulley and holds it firm while the nut is undone or tightened up.
in stock
6 Volt alternator, 90 mm diameter, overhaul in exchange, old part delivery after receipt of the product
Please indicate to us when placing your order, if you need an alternator with tapped holes for mounting the controller!
in stock
95mm Dynamo/Alternator Top Pulley “C” Spanner
This “C” Spanner has been made to fit top pulleys with a diameter of 95mm, hooks into the notch on the rear of the pulley and holds it firm while the nut is undone or tightened up.
in stock
99mm Dynamo/Alternator Top Pulley “C” Spanner
This “C” Spanner has been made to fit top pulleys with a diameter of 99mm, hooks into the notch on the rear of the pulley and holds it firm while the nut is undone or tightened up.
AC motor with 3 connector, for external control, overhaul in exchange, old part delivery after receipt of the product
The old deposit of 50.00 EUR is included in the purchase price and will be refunded upon exchangeable old part.
in stock
Alternator conversion kit, fits for Beetle, Bus T1
this kit includes; alternator with built-in voltage regulator alternator bracket tie-down strap set of three backing plates fits for: Beetle, except 25+ 30 hp The pulley 903 111 109 A suitable for 105 mm alternators is also required
in stock
Alternator key with 21mm and 36mm wrench size
36mm at one end and 21mm at the other end (21mm is for the later alternator nuts) Fan pulley wrench, much smaller and lighter than a full size 36mm wrench. This key is made of robust tool steel and galvanized.
in stock
Alternator/dynamo back plate set
fits for 34 to 50hp type 1 engines for alternator or dynamo with 105mm diameter consisting of inner and outer plate for fan housing and stiffening flange spare part numbers for comparison 131 119 259, 131 119 261 & 131 119 271
in stock
Ball bearing for dynamo, fits various types
fits for armature of all DC alternators two pieces required per dynamo
Ball bearings for alternator, fit for various types
passend für Anker aller Gleichstrom-Lichtmaschinen zwei Stück pro Lichtmaschine erforderlich
Belt pulley for dynamo, fits Bus T2 (from 08/68)
for dynamos 211 903 031 D & 211 903 031 E fits for Bus T2 (from FIN 219 2000 001) Type 181 (M 63) original spare part, NOS only few available
Cable harness fits for Type 181
Diese Kabelbäume werden nach US-Spezifikationen hergestellt und können im Vergleich zu europäische Modellen Abweichungen aufweisen. Für europäische Modelle und Sonderausstattungen müssen somit entsprechende Änderungen oder Ergänzungen...
in stock
Double ended Dynamo / Alternator pulley spanner will fit the 99mm and 108mm pulleys
This tension wrench for the upper pulley of the alternator can be used to loosen and fasten 6 V and 12 V pulleys can be loosened and tightened. It hooks into the notch on the back of the pulley and then holds it in place while you want...
in stock
Electronic controller for DC lighting machine, 12 volts, Bosch
under the rear seat or in the engine compartment
in stock
Inspection cover for dynamo with 105mm diameter
fits for the following dynamos: 113 903 031 G / 113 903 031 K / 113 903 031 M / 113 903 031 P & 113 903 031 Q
Nabe des Kühlgebläserades, für Typ 1-Motoren
passend für Käfer Karmann Ghia Typ 147 Fridolin Bus T1 Bus T2 (bis FIN 218 220 000) Typ 181 (außer M 63) Original-Ersatzteil, NOS ersetzte Mitte der 60er Jahre 111 119 123
in stock
Pulley for alternator, for engines (from 08/65)
for 6 & 12 Volt for 105mm dynamos & three phase alternators fits for Beetle (from VIN 116 000 001) Karmann Ghia (from VIN 146 000 001) Type 147 (from VIN 146 000 001) Bus T1 (from FIN 217 000 001) Bus T2 (1300 & 1600cc) Type 181 spare...
in stock
Riemenscheibe für 2. Drehstrom-Lichtmaschine, passend für Bus T2 & Typ 181
für Fahrzeuge mit M 51 passend für Bus T2 Typ 181 Original-Ersatzteil, NOS nur wenige vorhanden
in stock
Rotary Current Generator, 55Ah
suitable for: Beetle Bus Karmann Ghia Type: Beetle 1200 1.2 (11) Beetle 1303 (13) Beetle 1600 i (Mexico) Beetle Cabriolet (15) Transporter T2 Notes: 55Ah Power in KW: 25,32,34,35,37 Version: without pulley, with B + screw on the housing,...
in stock
Stiffening flange for cooling fan cover, fits type 1 engines (from 08/65)
for dynamos with 105mm Ø fits for Beetle Karmann Ghia Type 147 "Fridolin" Bus T1 Bus T2 Type 181 "Thing" original spare part, NOS limited quantity
in stock
Stiffening flange for cooling fan cover, fits type 1 engines (from 08/65)
for dynamos with 105mm Ø fits for Beetle Karmann Ghia Type 147 "Fridolin" Bus T1 Bus T2 Type 181 "Thing" reproduction, NOS with storage traces
in stock
Suppressor for radio interference suppression, fits various models
fits for Bus T2/T3 with M 632 type 181 with M 63 original spare part, NOS single item
Voltage regulator 12 Volt, fits for Beetle
Voltage regulator 12 Volt fits for: Bus T2, 1968-1979 Beetle 1200, 1978-1985 Beetle 1200/1300, 1947-1978 Beetle 1302/1303, 1971-1980 Type 3 1500/1600, 1961-1973 Bucket car 181, 1969-1982
in stock
Voltage regulator 6 Volt for alternator
Our tip : If you want to keep the original look, you can take over the cover of your old regulator, since the cover is only screwed.
Viewed