front axle - front axle T2 08/67-07/79
Novelties
No results were found for the filter!
in stock
in stock
Carrying Lever left bottom with Carrying Joint T 2, overhaul
Bus, please indicate whether 1.0 or 1.2 tons of additional load are present!
Carrying Lever right bottom with Carrying Joint T 2, overhau
Bus, please indicate whether 1.0 or 1.2 tons of additional load are present!
Carrying lever stop below, fit for buses from 08/67-07/79 T 2
Fitting Position: Torsion Bar, Lower Front Axle Material: Elastomer
in stock
Carrying lever, left, below, with ball joint, suitable for Bus T2 up to 07/69, overhauled in AT
Carrying lever left below with ball joint suitable for Bus T2 up to 07/69 overhauled in AT
in stock
in stock
Flange for steering column, fits Bus T2 & LT
fits for Bus T2 LT 1st generation (all, but LT40 & 45 only from VIN 28A 0005 294 - October 1979) original spare part, NOS Single item
Front Axle Body, 8/69 - 7/79 only fit 1,2 t front axle weight
only 1.2 ton ! many buses have only a front axle load of 1.0t there this axle does not fit !!!! bearing lever, spring assembly, spring assembly fastening are different than those of a 1.0 ton axle! original spare part, NOS with mounting...
in stock
in stock
Grease cap front, fits Bus T1, T2 & Brasil T1 (08/63 to 07/70)
without hole for speedometer cable fits for Bus T1 (from VIN 1 144 282) Brasil T1 Bus T2 (up to VIN 210 2300 000) Spare part number for comparison 211 405 692 A
in stock
in stock
in stock
in stock
in stock
Puma Style lowering system(weld on adjuster) per Pair Bus until 07/79
Mit den Rasterplatten können Sie Ihre vorhandene Original-Vorderachse in eine verstellbare 'Puma-Achse' umbauen. Die präzise Feinverzahnung erlaubt eine perfekte Höhen- und Härte-Justierung vorzunehmen. Das flache Design, das trotzdem...
in stock
Replacment boot for ball joint for front torsion arm, fits for bus T2
passend für T2 68-79 oben und unten Passend für T3 80-92 nur unten
in stock
in stock
in stock
Standard ball joint for front torsion arm, fits for Bus T2
fitting details: The outer diameter of this ball joint (at the knurl section) is 48.3mm. There should be a minimum overlap/interference of 0.2mm between the joint and the torsion arm bore. It is important that the torsion arm bore is...
in stock
Steering knuckle left, fits Bus T2 (from 08/72), used
fits for Bus T2 (from 213 2000 001) original spare part, used limited quantity
in stock
Steering knuckle set, dropped, for ball joint
Mit diesen Achsschenkeln können Sie Ihren Bus rund 6cm dem Boden näher bringen. Selbstverständlich können alle anderen Achsteile wie Tragarme, Spurstangenköpfe und Kugelgelenke weiter verwendet werden. Wir empfehlen in diesem...
Traghebel rechts unten mit Traggelenk Bus T2 (bis 07/69), überholt im AT
Bolzenlänge Stoßdämpferbefestigung 45 mm passend für Bus T2 bis 07/69 überholt im Austausch Altteillieferung vorab Lagerstellen des Traghebels dürfen nicht stark verschlissen sein oder Fressspuren haben
Viewed