Fridolin Typ 147 - Rear Axle
Novelties
No results were found for the filter!
in stock
Rear axle seal kit with outer spacer, fits models with swing axle, Made in Germany
original rear axle seal kit for one wheel. included in delivery are outer spacer (Bus T1 only up to VIN 1 144 281) O-rings Paper seals Thrust washer Oil seal Split pin
in stock
Rear suspension link with bushing, complete, left/right
fit for swing axle Beetle 10/68- Karmann GHia 10/68 Kübel 08/69 - 02/73
in stock
Rear wheel bearing inner spacer (swing axle)
Fitting Position: Rear Axle / Inner Axle: Swing Axle Diameter 1/Diameter 2: 30/43mm
in stock
Rear Wheel Beering, Fits for all vehicles with swing axle, exception Bus T1 only up to 07/63
Fits for all vehicles with swing axle Exception Bus T1 only up to 07/63 Diameter of the outer wheel bearing 72 mm Diameter of the radial shaft seal 60mm
Reparatursatz für Ausgleichsfeder der Hinterachse Bj. 08/66-10/68
inkl. Dämpfungsringen, Anschlägen, Führungen, Hülsen und Buchsen
in stock
Right-hand torsion bar, fits Beetle & Karmann Ghia (from 08/59)
Länge 522/523mm, Ø 22mm für Fahrzeuge mit Pendelachse ohne Ausgleichsfeder passend für Käfer (ab FIN 2 528 668) Karmann Ghia (FIN 2 528 668 bis 146 1021 300) Original-Ersatzteil, NOS begrenzte Stückzahl
in stock
Right-hand torsion bar, fits various models (up to 01/80)
length 626mm, Ø 24mm marked with two white colored rings fits for Type 3 squareback (up to FIN 366 500 000) Type 147 "Fridolin" Type 181 "Thing" original spare part, NOS limited quantity
in stock
Safety snap ring for drive shaft head
fits for: Beetle, Inclined control arm rear axle Typ 3, Inclined control arm rear axle Karmann Ghia, Inclined control arm rear axle Typ 34, Inclined control arm rear axle Bus T2, 1968-79 Bus T3 Golf MK1 Golf MK2
in stock
Sealing set for rear swing axle
includes Seals Simmering + Splint Brazil 2 Seal Kits required for 1 vehicle
in stock
Sechskantschraube M 10 x 19, 10 K, passend für verschiedene Modelle (09/65 bis 07/85)
für Tellerradbefestigung passend für Käfer (FIN 117 000 001 bis FIN 110 3100 000) Käfer Standard, Mexico, nicht 1302/1303 (08/66 bis 07/85) Karmann Ghia Typ 14 (ab FIN 147 000 001) Typ 147 Bus T1 (ab FIN 216 028 432) Typ 3 (ab FIN 316...
Semi-trailing arm right, glass bead blasted and high-gloss powder coated
Right trailing arm used but sandblasted and primed, without bearings and bushings. When ordering, please note whether you need this article by Dec. or from Dec. 70, or whether the feather sword has the single or double attachment. Tip:...
in stock
Set of rear axle bearing cap screws
Set consists of 4 pieces, M10x35 Original part number is only used for comparison 311 501 325 fit for Beetle from 57 and Karmann from 57 Type 181 08/69-02/73 Bus T1 to 07/67
Spacer ring outside for rear wheel bearing, fits models with swing axle
fits for Beetle Karmann Ghia type 14 & 34 Type 147 Type 181 Bus T1 1200 (up to VIN 1 144 281) Bus T1 1500 (from VIN 1 041 014) Type 3 (until VIN 361 2218 303) original spare part, NOS limited quantity
in stock
Stabilisatorreparatursatz mit Schubstangen
passend für Käfer ab (Fahrgestellnummer: 119 381 001) ab 10/68 passend für Karmann Ghia ab (Fahrgestellnummer: 149 381 001) ab 10/68 besteht aus folgenden Teilen : 113 501 819 A, 113 501 820 A, 2x 113 501 737 A und 2x 111 413 381 A...
in stock
Standard wheel bolt, fits various models
M14x1,5x19 fits for Beetle (from VIN 117 000 001; standard Beetle from VIN 118 000 001) Karmann Ghia (from VIN 147 000 001) Type 147 (from VIN 148 000 001) Bus T1 Bus T2 (up to VIN 210 2300 000) Type 3 (from VIN 316 000 001) Type 34...
in stock
Stop buffer for rear axle, fits various models
fits for Beetle (from VIN 2 528 668) Karmann Ghia type 14 (from VIN 2 528 668) Karmann Ghia type 34 Type 147 Type 3 with swing axle (Squareback only with M263 & M267)
in stock
Tail Stabilizer 19mm, suitable for all models with IRS rear Axle
Tail Stabilizer 19 mm for all models with IRS rear Axle fit for Beetle Karmann Ghia Type 14 Karmann Ghia Type 34 Type 3
in stock
Torsion Arm Cover Bolt, M10x18 wrench size 15, year 08/59 on
the right screw with a 15 mm wrench size
in stock
Torsion Bar Cap for Swing Axle, original quality, fits Beetle & Karmann Typ 14 (08/59 up)
Torsion Bar Cap for Swing Axle black fit for Beetle from 08/59 Karmann Ghia Type 14 from 08/59 Karmann Ghia Type 34 Type 3 original quality
in stock
Torsion Bar Cap, chrome, for Swing Axle, fit from year 08/59
Torsion Bar Cap for Swing Axle Material: chrome fit for Beetle from 08/59 Karmann Ghia Type 14 from 08/59 Karmann Ghia Type 34 from 08/59 Type 3 from 08/59 Made by WERK34
in stock
Torsion bar cover for double leaf spring sword trailing arms, chrome
Torsion bar cover for double leaf spring sword slanting handlebars chrome fits for: Beetle Karmann Ghia Type 3 Made by WERK34
in stock
Torsion bar cover for single spring sword semi trailing arm original part
für Käfer, Karmann Ghia und Typ 3
Wheel bolt for PCD 5x205, fits various models (till 01/80)
M12 x 1,5 x 13 fits for Beetle (up to VIN 116 1021 300; standard beetle up to VIN 117 999 000) Karmann Ghia (up to VIN 146 1021 300) Type 147 (up to VIN 147 999 000) Type 181 Type 3 (up to VIN 315 220 883) Type 34 (up to VIN 345 220 883)
Viewed