Bus T3 - rear axle
Novelties
No results were found for the filter!
in stock
in stock
in stock
in stock
Cap screw, M8x48, for constant velocity joint (24 pieces recommended)
fits for: Golf/Jetta, 1.1-1.8 (incl. D), 02/74-02/84 Golf/Jetta, 1.0-1.8 (incl. D), 08/83-12/92 Bus T3, 1.6-2.1 (incl. D), 05/79-07/92 Porsche 914, 1.7-2.0, 01/69-02/76
in stock
Castle nut M 30 x 1.5, fit for Bus (08/63 to 07/92)
wrench size 46 mm fits for Bus T1 (from VIN 1 144 282) Bus T2 Bus T3
in stock
Cotter for castellated nut, fits various models
5mm x 55mm fits for Bus T1 (from FIN 1 144 281) Bus T2 Bus T3 Type 181 Thing Do not reuse cotters, always replace them!
in stock
Cover Cap, Securing Bolt, Rear Trailing Arm
Kunststoff-Abdeckkappe Für die Schraube der Hinterachsschwinge left or right All VW T3
in stock
Cover washer for safety cap, fits various models (08/67 to 07/92)
of the manual or automatic transmission fits for manual transmission of Bus T2 Bus T3 Type 4 fits for automatic transmission of Beetle (from VIN 118 071 440) Karmann Ghia (from VIN 148 071 440) original spare part, NOS limited quantity...
in stock
in stock
in stock
in stock
Drive shaft, Automatic, left, fits for Bus T3 08/82-07/92
fits for: Bus T3, 08/82-07/92 includes mounting material length: 522mm
in stock
Drive shaft, automatic, right, fits for Bus T3 08/82-07/92
fits for: Bus T3, 08/82-07/92 Inclusive mounting material length: 570
in stock
Drive shaft, fits left or right Bus T3 01/83-07/92
Mounting material included Technical data: Installation side Rear axle on both sides Length [mm] 542 Joint diameter, gearbox side [mm] 100 Bore-Ø [mm] 8,2 Number of bores 6 Bolt circle Ø [mm] 86 Joint diameter wheel side [mm] 100 Gearbox...
in stock
in stock
Handbrake cable clip (per pair) for IRS axle
fits for Beetle Karmann Ghia, type 14 Type 3 Karmann Ghia, type 34 Type 181 Bus T3 (until 07/84) spare part numbers for comparison 113 501 595 & 251 501 595 A
in stock
Hose tie for joint protection boot, fits Bus T2 & T3
fits for Bus T2 Bus T3 original spare part, NOS few available
in stock
in stock
in stock
Querlenker Set, hinten rechts und links, passend für Bus T3
Querlenker links und rechts inklusive Gummilager passend für: Bus T3, alle (außer 16 Zoll Syncro) Neuteil Einbau Tip: den Querlenker vor Einbau mit Hohlraumversiegelung (z.B. Mike Sanders) behandeln
in stock
Radbolzen vorne, passend für Bus T3 & Bus T2 (ab 08/70)
Länge 52mm passend für Bus T2 (ab FIN 211 2000 001) Bus T3 Original-Ersatzteil, NOS begrenzte Stückzahl
in stock
Repair plate for spring seat on wishbone, fit for Bus T3
New lower spring seat to repair the wishbone. Allows to fix your rear rusty wishbone of a T3 and T4
in stock
Reparatursatz Gleichlaufgelenk passend für Modelle von 08/67-07/92
passend für: Bus ab Bj 68 - 91 Kübel ab Bj 08/73 411/ 412
in stock
in stock
Safety snap ring for drive shaft head
fits for: Beetle, Inclined control arm rear axle Typ 3, Inclined control arm rear axle Karmann Ghia, Inclined control arm rear axle Typ 34, Inclined control arm rear axle Bus T2, 1968-79 Bus T3 Golf MK1 Golf MK2
in stock
Screw for joint flange
suitable for: Bus T2 Bus T3 Bus T4 Bus T5 grade 12.9 M10x1,5 internal serration Made in Germany
in stock
Sealing cap for flange
fits for Bus T2 Bus T3 (manual transmission) Bus T4 (up to transmission no. 06034)
in stock
Shaft seal rear wheel bearing, fits Bus T2 & T3
fits for Bus T2 68-79 Bus T3 80-92 original spare part part numbers for comparison: 211 501 317, 211 501 317 A & 211 501 317 B
in stock
Shaft seal to drive shaft, fits for bus T2 from 08/75 and T3
Fits for right or left Not for automatic OE quality Made in Germany
in stock
Stub axle rear, fits for Bus T2
Stub axle rear fits for: Bus T2, 08/70-07/92 Length Stub axle: 175 mm
Upper sping packing
passend für Bus T3 + T4 Federteller-Unterlage oben beim Bus T4 verbaut bei Fahrzeugen mit 16 Zoll Felgen pro Fahrzeug werden zwei Unterlagen benötigt dieser Federteller hat eine Höhe von 13 mm
in stock
Upper underlay for coil spring, suitable for Bus T3+T4
fits for Bus T3 and T4 part numbers for comparison 251 511 149 & 7D0 511 147 A
in stock
Washer for Shock Absorber, fit for Bus T3 + T4
passend für Bus T3 + T4 Stückpreis beidseitig verwendbar für Vorder- und Hinterachse L: 51 mm, B: 51 mm, H: 7 mm
in stock
Wheel bolt rear, fits Bus T3 & Bus T2 (from 08/70)
Length 34,5mm length 34,5mm fits for Bus T2 (from VIN 211 2000 001) Bus T3
in stock
Wishbone, rear left, fits for Bus T3
Wishbone rubber bearing included fits for: Bus T3, all (except 16 inch Syncro) New part Installation tip: treat the control arm before installation with cavity sealant (eg Mike Sander)
in stock
Wishbone, rear right, fits for Bus T3
Wishbone rubber bearing included fits for: Bus T3, all (except 16 inch Syncro) New part Installation tip: treat the control arm before installation with cavity sealant (eg Mike Sanders)
Viewed