Bus T1 - alternator/generator for all engines upright fanshroud
Novelties
No results were found for the filter!
in stock
108mm Dynamo/Alternator Top Pulley “C” Spanner
This “C” Spanner has been made to fit top pulleys with a diameter of 108mm, hooks into the notch on the rear of the pulley and holds it firm while the nut is undone or tightened up.
in stock
6 Volt alternator, 90 mm diameter, overhaul in exchange, old part delivery after receipt of the product
Please indicate to us when placing your order, if you need an alternator with tapped holes for mounting the controller!
in stock
95mm Dynamo/Alternator Top Pulley “C” Spanner
This “C” Spanner has been made to fit top pulleys with a diameter of 95mm, hooks into the notch on the rear of the pulley and holds it firm while the nut is undone or tightened up.
in stock
99mm Dynamo/Alternator Top Pulley “C” Spanner
This “C” Spanner has been made to fit top pulleys with a diameter of 99mm, hooks into the notch on the rear of the pulley and holds it firm while the nut is undone or tightened up.
AC motor with 3 connector, for external control, overhaul in exchange, old part delivery after receipt of the product
The old deposit of 50.00 EUR is included in the purchase price and will be refunded upon exchangeable old part.
in stock
Alternator conversion kit, fits for Beetle, Bus T1
this kit includes; alternator with built-in voltage regulator alternator bracket tie-down strap set of three backing plates fits for: Beetle, except 25+ 30 hp The pulley 903 111 109 A suitable for 105 mm alternators is also required
in stock
Alternator key with 21mm and 36mm wrench size
36mm at one end and 21mm at the other end (21mm is for the later alternator nuts) Fan pulley wrench, much smaller and lighter than a full size 36mm wrench. This key is made of robust tool steel and galvanized.
in stock
Alternator/dynamo back plate set
fits for 34 to 50hp type 1 engines for alternator or dynamo with 105mm diameter consisting of inner and outer plate for fan housing and stiffening flange spare part numbers for comparison 131 119 259, 131 119 261 & 131 119 271
in stock
Ball bearing for dynamo, fits various types
fits for armature of all DC alternators two pieces required per dynamo
Ball bearings for alternator, fit for various types
passend für Anker aller Gleichstrom-Lichtmaschinen zwei Stück pro Lichtmaschine erforderlich
Bearing shield for 6V dynamo, fits various models
blower wheel side fits the following dynamos 211 903 021 113 903 021 A 113 903 021 C original spare part, NOS with light storage traces few available
in stock
Bolt for 90mm Ø dynamo housing, fits various models
fits for alternator with 90mm diameter Bus T1 Beetle Karmann Ghia type 14 Fridolin type 147 original spare part, NOS few available
in stock
in stock
in stock
in stock
in stock
in stock
Double ended Dynamo / Alternator pulley spanner will fit the 99mm and 108mm pulleys
This tension wrench for the upper pulley of the alternator can be used to loosen and fasten 6 V and 12 V pulleys can be loosened and tightened. It hooks into the notch on the back of the pulley and then holds it in place while you want...
in stock
Electronic controller for DC lighting machine, 12 volts, Bosch
under the rear seat or in the engine compartment
Feldspule 1 für 6V-Lichtmaschine, passend für verschiedene Modelle
passend für folgende Lichtmaschinen 211 903 021 113 903 021 A 113 903 021 C Original-Ersatzteil, NOS Einzelstück
in stock
Feldspule 1 für 6V-Lichtmaschine, passend für verschiedene Modelle
passend für folgende Lichtmaschinen 211 903 021 113 903 021 A 113 903 021 C Original-Ersatzteil, NOS wenige vorhanden
in stock
Feldspule 2 für 6V-Lichtmaschine, passend für verschiedene Modelle
passend für folgende Lichtmaschinen 211 903 021 113 903 021 A 113 903 021 C Original-Ersatzteil, NOS wenige vorhanden
in stock
Generator
originale Bosch Gleichstromlichtmaschine passt bei Bus T1 & 2 mit Typ 1 Motor bis 08/79, Käfer, Karmann Typ 14 und Kübel wir empfehlen auf jeden Fall einen neuen Regler, da wenn der Regler auch defekt ist kann er die neue Lichtmaschine...
Generator 6V 105 mm Diameter, old parts delivery after receipt of the product
The deposit of 50,00 EUR is included in the purchase price. Upon reciept of the exchangeable used part, the deposit will be refunded.
in stock
in stock
in stock
in stock
Halteplatte für 6V-Lichtmaschine, passend für verschiedene Modelle
passend für folgende Lichtmaschinen 211 903 021 113 903 021 A 113 903 021 C Original-Ersatzteil, NOS wenige vorhanden
in stock
Haltering für 6V-Lichtmaschine, passend für verschiedene Modelle
passend für folgende Lichtmaschinen 211 903 021 113 903 021 A 113 903 021 C Original-Ersatzteil, NOS wenige vorhanden
in stock
Inspection cover for dynamo with 105mm diameter
fits for the following dynamos: 113 903 031 G / 113 903 031 K / 113 903 031 M / 113 903 031 P & 113 903 031 Q
Nabe des Kühlgebläserades, für Typ 1-Motoren
passend für Käfer Karmann Ghia Typ 147 Fridolin Bus T1 Reproduktion der Mitte der 60er Jahre entfallenen Nabe 111 119 123
in stock
Nabe des Kühlgebläserades, für Typ 1-Motoren
passend für Käfer Karmann Ghia Typ 147 Fridolin Bus T1 Original-Ersatzteil, NOS begrenzte Menge Mitte der 60er Jahre entfallen und durch 111 119 123 A ersetzt
Nabe des Kühlgebläserades, für Typ 1-Motoren
passend für Käfer Karmann Ghia Typ 147 Fridolin Bus T1 Bus T2 (bis FIN 218 220 000) Typ 181 (außer M 63) Original-Ersatzteil, NOS ersetzte Mitte der 60er Jahre 111 119 123
in stock
Pulley alternator chrome, 105 mm diameter
suitable for 6 Volt + 12 Volt DC Lima as well as for three-phase Lima
in stock
Pulley for alternator, for engines (from 08/65)
for 6 & 12 Volt for 105mm dynamos & three phase alternators fits for Beetle (from VIN 116 000 001) Karmann Ghia (from VIN 146 000 001) Type 147 (from VIN 146 000 001) Bus T1 (from FIN 217 000 001) Bus T2 (1300 & 1600cc) Type 181 spare...
in stock
Pulley for dynamo, fits type 1 engines (08/55 to 05/60)
for 30HP engines with 90mm dynamo fits for Beetle (engine no. 1 120 615 to 1 311 073) Karmann Ghia (engine no. 1 120 615 to 1 311 073) Bus T1 (engine no. 1 120 615 to 3 999 999)
in stock
in stock
Reinforcement flange for cooling fan cover, fits type 1 engines (till 07/65)
for dynamos with 90mm Ø fits for Beetle Karmann Ghia Type 147 "Fridolin" Bus T1 original spare part, NOS limited quantity
in stock
Reparatur Kabel für Regler/ Lichtmaschinen Anschluss
Länge 12,5 cm Kabelquerschnitt 4mm² Kabelschuh Innendurchmesser 5,1 mm Ø wenige verfügbar
in stock
Rotary Current Generator, 55Ah
suitable for: Beetle Bus Karmann Ghia Type: Beetle 1200 1.2 (11) Beetle 1303 (13) Beetle 1600 i (Mexico) Beetle Cabriolet (15) Transporter T2 Notes: 55Ah Power in KW: 25,32,34,35,37 Version: without pulley, with B + screw on the housing,...
in stock
Schutzscheibe für 6V-Lichtmaschine, passend für verschiedene Modelle
passend für folgende Lichtmaschinen 211 903 021 113 903 021 A 113 903 021 C Original-Ersatzteil, NOS wenige vorhanden
in stock
Spring washer for 6V dynamo, fits various models
fits for the following dynamos 211 903 021 113 903 021 A 113 903 021 C original spare part, NOS few available
in stock
Stiffening flange for cooling fan cover, fits type 1 engines (from 08/65)
for dynamos with 105mm Ø fits for Beetle Karmann Ghia Type 147 "Fridolin" Bus T1 Bus T2 Type 181 "Thing" original spare part, NOS limited quantity
in stock
Stiffening flange for cooling fan cover, fits type 1 engines (from 08/65)
for dynamos with 105mm Ø fits for Beetle Karmann Ghia Type 147 "Fridolin" Bus T1 Bus T2 Type 181 "Thing" reproduction, NOS with storage traces
in stock
Three-phase alternator, reinforced (75Ah), suitable for Beetle and Bus T2
with 1-fold plug and integrated controller fits for Käfer (from 08/67) Bus T2, 1600
in stock
in stock
in stock
Viewed