181 Thing
Novelties
No results were found for the filter!
in stock
Adjustable spring plates (Per Pair) 627 mm
This adjustable torsion bar Swords enable raising or lowering by 40mm by simply adjusting the adjusting screw which is accessible even with mounted wheel. A must for drag racing cars to make fine adjustments on the circuit can, however,...
Adjustable spring plates (Per Pair) 675 mm
This adjustable torsion bar Swords enable raising or lowering by 40mm by simply adjusting the adjusting screw which is accessible even with mounted wheel. A must for drag racing cars to make fine adjustments on the circuit can, however,...
in stock
Adjusting nut for pivot pin, fits various models
for the following clutches 211 141 025, 211 141 025 A, 211 141 025 B, 211 141 025 C, 211 141 025 D, 311 141 025, 311 141 025 B & 311 141 025 D 3 pieces are needed per vehicle installed in Beetle Karmann Ghia Bus T1 Type 3 Type 34 Type...
in stock
Adjusting nut of the pivot bolt, for various models (from 07/62)
for clutch (200mm) 211 141 025 B, 311 141 025 D & (215mm) 043 141 025 A fits for Beetle (engine code: L, H & B) Karmann Ghia (engine code: L, H & B) Bus T1 (from engine no. 6 908 639) Type 181 Bus T2 (1300 & 1600cc) original spare part,...
in stock
Adjusting screw for brake shoes, fit from 08/64
fit for: Beetle (from VIN 115 000 001) Karmann Ghia Type 14 (from VIN 145 000 001) Type 147 Type 3/34 (08/64 to 07/65, VIN 315 000 001 to 315 220 883) Type 181 (front all, rear from 03/73, VIN 183 2346 525) spare part number to compare:...
in stock
Adjusting screw for steering spindle, suitable for roller steering from 08/61
suitable for: roller steering from year of construction 08/61
in stock
Adjusting screws for brake shoes
fits for: Bus T1 (from 03/55, VIN 20 - 117 902) Bus T2 Type 181, rear only (up to 02/73, FIN 183 2346 524) 4 pieces spare part number to compare: 211 609 209 A
in stock
Air baffle bottom left, galvanized, top quality, fit for 25 kW (34 HP)
This galvanized air baffle for the tappet protection tubes has the nuts and mounting holes in the right place. No rework is necessary like with inexpensive repros.
in stock
Air baffle bottom left, galvanized, top quality, fits 29-37 kW (40-50 hp)
This galvanized air baffle for the pushrod protection tubes has the nuts and mounting holes in place. No rework is necessary as with the inexpensive repros.
in stock
Air baffle bottom, front right, galvanized, top quality, 25 kW (34 hp)
This galvanized air baffle for the pushrod protection tubes has the nuts and mounting holes in place. No rework is necessary as with the inexpensive repros.
in stock
Air baffle bottom, front right, galvanized, top quality, 29-37 kW (40-50 hp).
This galvanized air baffle for the pushrod protection tubes has the nuts and mounting holes in place. No rework is necessary as with the inexpensive repros.
in stock
Air baffle bottom, right rear, galvanized, top quality, 25 kW (34 hp)
This galvanized air baffle for the pushrod protection tubes has the nuts and mounting holes in place. No rework is necessary as with the inexpensive repros.
in stock
Air baffle bottom, right rear, galvanized, top quality, 29-37 kW (40-50 hp).
This galvanized air baffle for the pushrod protection tubes has the nuts and mounting holes in place. No rework is necessary as with the inexpensive repros.
in stock
Air conditioning cleaner
Cleans and disinfects the entire air conditioning and heating systems. Gets rid of germs and bacteria, and refreshes the interior of the vehicle in the long term. intensive foam cleaning easy to use long-term disinfection hose included...
Air guide plate rear right, fits 1.3 to 1.6 (from 08/67)
fits for 1.3 to 1.6 engines from 08/67 Beetle Bus T2 Thing 181 Karman Ghia Type 14
in stock
Alarm pull rotary switch, fits various models (08/69 to 2004)
for vehicles with police equipment fits for Bus T2 to T4 (from VIN 219 300 000) Type 181 Golf MK1 to Golf MK2 Scirocco MK1 to MK2 Jetta MK1 to MK2 Vento Passat MK1 LT MK1 Original spare part, NOS part number for comparison 211 951 275 A
in stock
Alternator conversion kit, fits for Beetle, Bus T1
this kit includes; alternator with built-in voltage regulator alternator bracket tie-down strap set of three backing plates fits for: Beetle, except 25+ 30 hp The pulley 903 111 109 A suitable for 105 mm alternators is also required
in stock
Alternator key with 21mm and 36mm wrench size
36mm at one end and 21mm at the other end (21mm is for the later alternator nuts) Fan pulley wrench, much smaller and lighter than a full size 36mm wrench. This key is made of robust tool steel and galvanized.
in stock
Alternator/dynamo back plate set
fits for 34 to 50hp type 1 engines for alternator or dynamo with 105mm diameter consisting of inner and outer plate for fan housing and stiffening flange spare part numbers for comparison 131 119 259, 131 119 261 & 131 119 271
Alu-Valve covers with ventilation , Evolution Type 1
German Product fits all Typ 1 engines except 24,5-30 HP
in stock
Alubutyl insulation mat, self-adhesive, width 60cm, price per meter (base price per sqm 27.86 €)
Price per meter width 60cm Thickness 1mm Very well for insulation and soundproofing Basic price per qm 27,68 € Made by WERK34
in stock
Aluminum oil cooler, standard
suitable for: Beetle, 1.6 year of construction 08/70 to 04/79 Bus T2, 1.6 from 08/70 to 07/71 Golf GTI, 1.6 + 1.8 GTI year 01/77 to 02/84 Scirocco GTI, 1.6 + 1.8 from 01/77 to 10/83
in stock
Anbausatz für Frontstabilisator, Edelstahl, passend für Karmann Ghia + Käfer ab Bj.66
Komplettset aus Edelstahl. Durch die Schraubfixierung ist die Montage des Stabilisators deutlich leichter. Gerade beim Umrüsten auf PU-Lager ist dies mit den originalen Schellen nahezu unmöglich.
Andrehklaue, passend für verschiedene Modelle
passend für Industriemotor Typ 122, 122/1, 122/2, 126 Typ 181 Kübelwagen Original-Ersatzteil, NOS Ausführung mit Loch durch Schaft 11,5 mm Ø Loch für die Kurbel 21 mm Ø Schaftlänge 25 mm M 20 Nut im Schaft gelb verzinkt wenige vorhanden...
in stock
Angle tube for master brake cylinder 2-circle, fits for 07/67-07/71
Angle tube for master brake cylinder 2-circle fits for 07/67-07/71
in stock
Angle tube for master cylinder 105°, fits for 08/66-07/69
Manufacturer ATE Angle tube for master brake cylinder 105 fits for 08/66-07/69
in stock
Anschlagstütze auf Hinterachsrohr, passend für Bus T1 & Typ 181
passend für Bus T1 (1500 & ab FIN 215 036 651) Typ 181 (mit Pendelachse, bis FIN 183 2346 524) Original-Ersatzteil, NOS mit Lagerspuren wenige verfügbar
Arbeitsstromrelais, universal
Hersteller HELLA passend für viele Anwendungen Original-Volkswagen-Zubehör, NOS begrenzte Stückzahl
in stock
Auspuffrohr rechts 155 mm, passend für Typ 181 Kübelwagen
passend für Typ 181 Kübelwagen original-Ersatzteile, NOS wenige verfügbar Außendurchmesser ca. 30 mm Ø Innendurchmesser ca. 35,5 mm Ø Außendurchmesser Flansch ca. 34 mm Ø Innendurchmesser Flansch ca. 30 mm Ø
Ausrückwelle, passend für verschiedene Modelle (08/70 bis 09/71)
passend für Käfer (FIN 111 2000 001 bis 112 2070 812; alle 1302 , nicht Standard mit kurzem Vorderwagen) Karmann Ghia Typ 14 (FIN 141 2000 001 bis 142 2070 812) Typ 181 (FIN 181 200 001 bis 181 3200 000) Typ 3 (FIN 311 2000 001 bis...
in stock
Ausrückwelle, passend für verschiedene Modelle (ab 09/71)
passend für Käfer (ab FIN 112 2070 813 bis Dezember 1985; auch 1302 und 1303 ) Käfer Standard (ab April 1972) Karmann Ghia Typ 14 (ab FIN 142 2070 813) Typ 181 (ab FIN 182 2000 001) Typ 3 (ab September 1971)
in stock
Automatic seat belt beige (each)
fits for: Beetle 08/64 and later Karmann Ghia 08/64 and later Bus 08/66 and later Type 3 06/64 and later Thing
in stock
Automatic seat belt grey (each)
fit for: Beetle 08/64 and later Karmann Ghia 08/64 and later Bus 08/66 and later Type 3 06/64 and later Thing
in stock
Axle journal, semi-trailing arm
fit for the following vehicles with semi-trailing arm rear axle Beetle Karmann Ghia Type 14 Type 3 Bus T1 -67 converted to semi-trailing arm rear axle Originalpartnumber is only used for comparison 113 501 231
in stock
Axle Seal closed, fits for Beetle + Typ 3 + Karmann Ghia + Bus T1
closed axle boot fits for: Beetle Typ 3, 1500/1600 Karmann Ghia Typ 14 Karmann Ghia Typ 34 Bus T1
in stock
Ball bearing for dynamo, fits various types
fits for armature of all DC alternators two pieces required per dynamo
Ball bearings for alternator, fit for various types
passend für Anker aller Gleichstrom-Lichtmaschinen zwei Stück pro Lichtmaschine erforderlich
Viewed